Search results for " power converters."

Power losses comparison between Silicon Carbide and Silicon devices for an isolated DC-DC converter

2021

In recent years, new efficient power devices have been implemented. Silicon Carbide has replaced silicon as regards the production and the utilization of many devices, such as MOSFETs, diodes, IGBTs and many others. SiC devices are characterized by a low reverse recovery charge, high carrier saturation velocity, by which it is possible to work at high frequency, and high breakdown voltage. Thanks to the great thermal conductivity and the wide bandgap, these devices can operate at high temperature and reach high voltages and currents. What is important to stress is the fact that power losses in SiC devices are lower than the silicon ones. These are the reasons why these devices are utilized …

Generalized power-angle control for grid-forming converters: A structural analysis

2022

Several control schemes have been recently proposed and studied as grid-forming controls for power converters. In all these schemes, the power-angle control loop is the part which defines the fundamental capabilities of the grid-forming control: that control loop governs in fact the inherent synchronization mechanism of the power converter, the power sharing with the other generation sources in the system and the oscillatory characteristics of the converter-based resource. This article introduces a general formulation for the power-angle control characterizing the grid-forming concept for power converters. The generalized power-angle control is based on a polynomial fraction formulation, an…

Power System Oscillations with Different Prevalence of Grid-Following and Grid-Forming Converters

2022

The oscillatory behaviour of the power system is an aspect that is significantly affected by the increasing integration of converter-based generation sources. Several works address the impact of non-synchronous generation on the operation of the system from different points of view, but only a few studies focus on power-frequency oscillations with a prevalence of generation sources interfaced through power electronics. A lack of research can be found in particular in the comparative analysis of the two main control strategies for power converters, namely grid-following and grid-forming. The article aims to contribute to this direction, starting from a theoretical analysis of the two control…

Comprehensive Modeling and Experimental Testing of Fault Detection and Management of a Nonredundant Fault-Tolerant VSI

2015

This paper presents an investigation and a comprehensive analysis on fault operations in a conventional three-phase voltage source inverter. After an introductory section dealing with power converter reliability and fault analysis issues in power electronics, a generalized switching function accounting for both healthy and faulty conditions and an easy and feasible method to embed fault diagnosis and reconfiguration within the control algorithm are introduced. The proposed system has simple and compact implementation. Experimental results operating both at open- and closed-loop current control, obtained using a test bench realized using a dSPACE system and the fault-tolerant inverter protot…

Achieving maximum power transfer in a multi-source renewable system

2014

Reducing DC Link Voltage Unbalance in a Fault-Tolerant Inverter

2014

Today, continuous working of power inverter drives is mandatory for several applications. Damages to materials, machines or even risks to human life have to be absolutely avoided. In the literature, fault-tolerant algorithms and architectures to achieve a successful fault handling are investigated. Researchers aim at reducing the number and cost of additional components, improving at the same time the inverter performances under postfault conditions. Cost, post-fault power derating and increasing distortion are usually conflicting requirements. In this paper, a fault-tolerant three phase inverter is presented. A reconfigurable architecture and a novel fault-tolerant algorithm is designed to…

Flexible power converters for the fault tolerant operation of Micro-Grids

2010

The progressive penetration level of Distributed Generation (DG) is destined to cause deep changes in the existing distribution networks no longer considered as passive terminations of the whole electrical system. A possible solution is the realization of small networks, namely the Micro-Grids, reproducing in themselves the structure of the main production and distribution of the electrical energy system. In order to gain an adequate reliability level of the microgrids the individuation and the management of the faults with the goal of maintaining the micro-grid operation (fault tolerant operation) is quite important. In the present paper flexible power converters and a companion control al…

Hybrid Modelling and Control of a Class of Power Converters With Triangular-Carrier PWM Inputs

2021

In this paper, a new control design procedure for a class of power converters based on hybrid dynamical systems theory is presented. The continuous-time dynamics, as voltage and current signals, and discretetime dynamics, as the on-off state of the switches, are captured with a hybrid model. This model avoids the use of averaged and approximated models and includes the PWM as well as the sample-and-hold mechanism, commonly used in the industry. Then, another simplified hybrid system, whose trajectories match with the original one, is selected to design the controller and to analyse stability properties. Finally, an estimation of the chattering in steady state of the voltage and current sign…

Identification and robust control of DC/DC converter Hammerstein model

2008

Abstract—This paper deals with model-based robust control of dc/dc power electronic converters. The converter is described by means of a Hammerstein model consisting of the nonlinear static characteristics of the converter and a linear time-invariant (LTI) uncertainmodel whose parameters depend on the actual duty-cycle operating range. This suggests that the controller be designed using robust control techniques. In view of applying robust control, identification of the earlier LTI models is performed by means of simulation experiments, carried out on a converter switching model implemented onMATLAB/SIMULINK environment. Internal model control (IMC) structure is employed for the controller …

Thermal Stability of a DC/DC Converter with Inductor in Partial Saturation

2021

Inductors operated in quasi saturation in dc–dc converters allow reduction of the core size and realization costs; on the other hand, they imply an increase of dissipated power that can jeopardize the thermal stability of the converter. In this article, this issue is studied by a mathematical model able to represent both the inductor nonlinearity and its temperature dependence. The main losses, such as ohmic, skin effect and magnetic, are taken into account in the model. The inductor is characterized by a polynomial curve whose parameters are a function of the temperature. Finally, the whole converter is modeled and simulation results, obtained on a boost converter, are compared with experi…